ARC-1886-6N2I
(PCIe Gen 4.0 M.2 NVMe Hardware RAID Adapter)

Per informazioi complete sul prodotto vai alla pagina WEB di Areca: ARC-1886-6N2i

 

HIGLIGHTS

✵PCIe 4.0 host interface, PCIe Gen4 x8 lanes at maximum transfer rate up to 128Gb/s

✵Hardware-based RAID solution that supports RAID levels 0, 1, 10, 3, 5, 6, Single Disk and JBOD

✵Implemented 8GB 72-bit DDR4-2666 SDRAM providing hardware RAID assist engine for parity calculations

✵Support off module power loss protection (PLP) saves data issued without data loss at power fail using optional CBM module

✵CBM module or on-board battery(CR2032) to keep on M.2 fault LED status for troubleshooting

✵Supports up to 6x PCIe Gen 4.0 M.2 slots and 2x 12Gb/s SAS/SATA ports

✵Dynamically allocate storage 12Gb/s SSA/SATA/PCIe (NVMe) to NVMe slot1 and SATA/SAS ports

✵Firmware automatically backup from NVMe RAID to SAS/SATA RAID

✵Device interface PCIe Gen4 NVMe / 6Gb/s SATA per M.2 slot

✵Controller-level hardware encryption

✵SED support for hardware disk encryption capable drives

 

 

PCIe Gen 4.0 M.2 NVMe Hardware RAID controller

banner of ARC-1886-6N2I

The ARC-1886-6N2I presents the advanced hardware RAID technology in enhanced performance of using 6 Bays M.2 NVMe and an improved enterprise data protection of using two SAS/SATA ports. The hardware RAID adapter accesses the data of NVMe disk array with a workload preset value. While the workload level stays within the preset value, the RAID adapter would constantly back up the data of NVMe disk array to the other two SAS/SATA ports hard disk arrays. This is designed in a 1.6 GHz dual-core ROC processor, DDR4-2666 memory and PCIe Gen 4.0 host/device interface and supports RAID levels 0, 1, 10, 3, 5, 6, Single Disk or JBOD.

 

 

PCIe Gen 4.0 M.2 NVMe Hardware RAID controller

ARC-1886-6N2I

ARC-1886-4N8I

Form Factor

107.2(H) x 262(L) mm

107.2(H) x 205(L) mm

I/O Processor

Tri-Mode Dual Core ARM A15 1.6GHz ROC

On-Board Cache

8GB on-board DDR4-2666 SDRAM

Drive Connector

2 x SATA

1 x SFF-8654 [X8]

&

&

6 x M.2 Connector

4 x M.2 Connector

Drive Support

12Gb/s SAS, 6Gb/s SATA, Gen 4.0 PCIe (NVMe)

Management Port

In-Band: PCIe / Out-of-Band: LAN Port

Enclosure Ready

SGPIO, SMP, SES2 and UBM

Operating Voltage

12V

Power Consumption

Approximately 14 Watts (without M.2 drive)

Cache Protection

ARC-1886-CBM

High Bandwith PCI-E 4.0 Support

To run the PCIe Gen 4.0 slots in Gen 4 speed, please must install the ROC which supports PCI Express 4.0. If you install the PCIe3.0 ROC, the PCI Express 4.0 slots will run only at Gen3 speed.

  • Higher bit rate - 16.0GT/s
  • Higher bandwidth per lane - 2GB/s
  • Higher efficiency - 98.5% encoding efficiency

The ARC-1886-6N2I RAID adapter can operate in all three modes concurrently servicing NVMe, SAS or SATA drives that offers the operation of NVMe, SAS or SATA storage devices in a single RAID adapter. With a single ARC-1886-6N2I RAID adapter, system integrators can take full advantage of 6x PCIe Gen 4.0 M.2 x2/x4 NVMe drives (or 6Gb/s M.2 SATA SSD drives) and 2x 12Gb/s SAS/SATA ports.